This product has been discontinued.
SeaStar Solutions
Merc. Control Cable, 10' - SeaStar Solutions
Price: $37.76
Discontinued
Save: $24.73
(39% Off $62.49)
Part # CC17910
(Discontinued)
  • Fits: Mariner Type 600A single lever control heads (1965-date)
  • Fits: Mariner motors except pre-1993 40 HP and less engines
  • Match both cable ends
    • Standard Replacement for MERCURY or MERC-CRUISER cables for current models with factory assembled connection kit
    • Fittings are stainless steel or brass
    • Stainless steel cable wire, lubricated for life
      • Fits: Mercruiser Type 600A single lever control heads (1965-date)
      • Fits: Mercruiser motors (1965-date)
      • Match both cable ends
Full StarFull StarFull StarFull StarFull Star
Based On 5 Reviews | Write Review
Full StarFull StarFull StarFull StarFull Star
Perfect fit
by Richard from Milton, New Hampshire on July 28, 2018
Super fast shipping, controls fit and work perfectly
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
Cables arrived in three days of ordering. Very well packaged.
by Michael from Cincinnati, Ohio on July 15, 2015
Cables were and exact match of the old cables and installed without any problems.
(1 of 1 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
merc control cables
by Tim from Oologah, Oklahoma on September 25, 2014
These cables worked great, easy to install and got here in 2 days.
(2 of 2 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
cables
by Jack from Battlecreek, Michigan on June 21, 2014
fit perfect
(1 of 2 people found this review helpful)
Was this review helpful?
Full StarFull StarFull StarFull StarFull Star
Cloes enough
by John from San Diego, California on June 03, 2013
This replacement cable was exact match to the original equipment EXCEPT that it is 6 inches longer. Better than being too short, works fine.
(4 of 6 people found this review helpful)
Was this review helpful?
Q:
I have an 18' Tracker pontoon (2003) and a 40 hp Mercury motor (2004). The drive cable and throttle cable have, for unknown reasons, broke the controler end plastic barrels off. the cable has a mfg of Uflex and a number 3992617 on coatin of the cable. Can you determine the length from that number? Can the plastic barrels be reattached? If so, what do you use to do so? I have not measured my cables because I hope I can replace the barrels and if I have to replace the cables I want to use them as pull lines for the new ones. Can you help?
A:
The number provided is a production number. The number that will show the length will start with C5. The barrels cannot be reattached.


Q:
I have 21' in/outboard starboard side shift mount?
A:
You will need to know the manufacturer of your I/O along with the length needed.


Q:
How do I measure these. End to end total?
A:
Yes just measure end to end on control cables to get length needed.


Q:
I have 1984 cheetah 180 with mercruiser 185 will this fit. I need both cables?
A:
Yes, this model of cable will work. You will need to verify length though as we do not have that original information.


Q:
Will this cable fit mid 80's 35 horse mercury outboard?
A:
Yes this is for that application, but you will want to verify if 10' is the length you need.


Q:
I know I would have to determine the length but what throttle cable do I need for a 1979 90 hp Mariner?
A:
You need the CC179 series.


Q:
Is this both cables?
A:
These are sold in individual cables. If you need two cables then you will need to order two. Just be sure the length you need is correct.


Ask a question
Question & Answer Guidelines
This product ships in 1 business day.
Add to Cart and enter your Postal Code to determine the shipping charges.
Most products and orders leave our warehouse in 1 business day. However, select items may take more processing time. Alaska and Hawaii orders please add 1 additional warehouse processing day.
Standard Shipping Policies